Getian Optoelectronics: The first series of high-power modules in the industry passed LM-80 certification

Recently, Getian Optoelectronics CNAS Lab released a message saying that all the Getian Optoelectronics high-power modules have passed the third-party Energy Star LM-80 certification. The certified products have created the most in several industries:

First, the module power source certification of maximum power, 300w;

Second, the module light source series covers the widest range, and the grid module series from 20w to 100w, 100w-300w two appearances, all power coverage;

Third, the first ceramic flip-chip module FCSL series in China has also passed the certification.

In this regard, it is the first in the industry. After 6,000 hours of rigorous testing and verification, each product has been successfully recognized by third-party laboratories for its excellent performance. It marks the dedication and technical strength of Getian Optoelectronics, and also indicates that Getian Optoelectronics enters the international market. Ability and confidence!

Xu Jinli, director of the GNAS Laboratory of Getian Optoelectronics, said that this time, the third party sent a total of two series

1, GT-P100 series: covering all power from 20-100w,

Report number: RSZ1411125054-10

TS: 85 ° C

6000 hour luminous flux maintenance rate: 96.53%

L70 life: 53,000 hours

2, GT-P500 series: covering all power from 100-300w;

Report Number: RSZ1411125055-10

TS: 95 ° C

6000 hour luminous flux maintenance rate: 96.06%

L70 life: 58,000 hours

After receiving the 300w inspection item, the third-party testing and certification organization can not reduce the TS point temperature of the 300w product to the standard 85°C with the best heat dissipation device, and finally reach an agreement with Getian to directly locate the TS point temperature. At 95 ° C, the problem is solved. This is the first time in the industry, and even third-party laboratories have never encountered it; the key is to improve the stability of the product under the aging verification of 10+% standard temperature. The third-party laboratory technicians were greatly amazed! Xu Jinli, director of the CNAS laboratory of Getian Optoelectronics, said.

According to Director Zhu of the research and development department of Getian Optoelectronics, these two products are boldly innovative on the basis of the technological precipitation of Getian for many years. They strictly control the selection of each raw material and adopt the leading packaging technology, which not only will the overall light effect of the product. It is the highest, (300w module product light efficiency of 130-140lm / w), but also maintain a stable light output. Such a large wattage is definitely not available in many packaging companies in the industry, and not many companies have such full confidence to invest so much money to do this high-risk thing.

The product has passed the LM-80 certification, and its significance is not only a bottoming out of the product life, but also a better benefit factor, which is more conducive to the use of the grid light source to export the lamps, especially the lighting products exported to the United States. Because the subsidy policy for energy-saving products introduced by the United States is very strong, subsidies for DLC-certified lighting products can be enjoyed, and products must pass DLC certification. The cost is very high, and the time must pass 6000 hours. The market entry threshold, time cost is the biggest cost, the business opportunity is almost gone in the past nine months, and for lamps that already have LM-80 light source, it can be solved in more than a week by DLC. In terms of cost, it also saves nearly 90%, and the risk of passing is almost zero. Therefore, the use of Grid-based LM-80 certified light source for the export of lamps, undoubtedly greatly reduced in cost, greatly improved efficiency, greatly reduced risk!

In the general-purpose products commonly found on the market, Getian Optoelectronics is always marked with a unique “GT LED” logo on the conspicuous part of the bracket. Figure:

For the user, it is very intuitive and the customer's rights and interests are better protected. When the user purchases, the authenticity can be quickly identified to avoid unnecessary losses.

About Silicone Card Holder
Hello, my name is silicone card holder,I am made of silicone and you need a card holder like me. Why?Because I have many advantages:
1.Good elasticity,can hold a lot of cards and other little things,such as earphone,key,coins etc.
2.I'm not fussy all different kinds of phone or tablete I can hold,as long as the surface is smooth.
3.I am made of Food Grade silicone, is a friend of safety product and environmental protection.
4.Don't worry if you contaminate me, I can be easy to clean and dry quickly.
5.I don't fear water,becacse the silicone is waterproof.
I have many features  you don't know, If you want to learn about me, you can take me home!

Silicone card holder introduction:
1.Product name:Silicone Phone Card Holder, Cell Phone Wallet , Card Holder Phone ,Card Holder for Phone,Phone Card Holder Sticker,3M Silicone Card Holder
2.Place of origin:Guangdong China
3.Color:any pantone color
4.Logo:Printing,debossed,embossed
5.MOQ:500pcs.
6.Package:1 pcs/opp,customized design is available.
7.Design:Customized/stock
8.Certification:FDA,LFGB,SGS,ROHS,etc.
9.Usage:Easy to collet cards

10.Silicone card holder photos for reference.

silicone card holder

Silicone Card Holder

Silicone Card Holder,Silicone Phone Card Holder, Cell Phone Wallet,Card Holder Phone,Card Holder for Phone,Phone Card Holder Sticker,3M Silicone Card Holder

OK Silicone Gift Co., Ltd. , https://www.oemsiliconegift.com

Posted on